1. Locate the spa's high-limit reset. This is a red button found on many spa packs.
  2. Turn on your spa and observe its operation.
  3. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How do I reset my hot tub control panel?
How to Reset a Spa Heater Locate the spa's high-limit reset. This is a red button found on many spa packs. ... Press the high-limit reset button. ... Turn on your spa and observe its operation. ... Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
Is there a reset button on a hot tub?
Generally speaking, it's a small red button that is also located on the control pack, if it is out (stiff), then it is popped. There are many different brands, about 95% are this way. If either one is tripped, there is usually something that caused it, as they are both for safety. Apr 25, 2015

Why did my hot tub stop working?

The first step to take is to check the circuit breaker panel that your hot tub is hooked up to. ... If this restores power to your tub temporarily before the breaker is tripped again, consult an electrician – the problem is likely with your breaker and not your spa. If this does not fix the problem, check the GFI switch. Jun 5, 2018
How do I test my spa control panel?
Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board. Feb 14, 2017
How do you reset a strong spa?
2. Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back on. The spa should have power again.
How much does a Caldera spa cost?
$9,000-$22,000+ The price covers great design, low running costs, maximum comfort, minimal maintenance, the best massage jets, and efficient operation. Luxury spas are likely to have: The best water care options. The best construction for the best durability.
How do I unlock my Jacuzzi control panel?
To unlock the panel, while holding down the "Temperature" button (or the "Up" button if you do not have the "Temperature" button), gently press and release the "Light" button twice.
How do you fill a Caldera spa?
Unscrew the Spa Frog cartridge caps and remove cartridge before filling. Fill your spa through the filter compartment (using the CleanScreen™ pre-filter that attaches to your garden hose if you are well water). The water level of your spa should be maintained at approximately one inch above the highest jet in the spa.
How do I know if my heating element is bad in my hot tub?
To test if a bad heater is causing your tripped breaker, you can disconnect the copper tabs (or wires) from the spa pack to the heater element. Once disconnected, turn the power back on. If the breaker stays on, you've determined that the heater is bad. Mar 4, 2016
How do you diagnose a hot tub problem?
Troubleshooting Common Hot Tub Issues Heater Failure. If the water in your spa isn't as warm as it should it, it may be an indication of heater failure. ... Clogged Filter. If water flow is poor and your jets don't seem to be working as well as they should, you may have a clogged filter. ... Air Lock. ... Noisy Pump. ... Tripped GFCI Breakers.

How do you reset hot tub after power outage?

If the GFCI has been tripped by a power surge or brownout, just pressing the “RESET” button, if there is one, will turn the circuit, and your hot tub, back on. Feb 29, 2016
Does hot tub heat up faster with jets on?
A hot tub will always heat up faster with jets. This is because it disburses the heated water throughout the tub more efficiently and breaks up any cold pockets hanging around in the pipes. And you can also put a cover over the hot tub with the heater and jets going to trap the heat inside.
Where is the high limit switch on my hot tub?
You'll find this high-level limit switch in your heater cabinet. With the front panel removed, look in the lower-left corner of the cabinet. Attached to the inside left surface you'll find a white switch with a red push button in its center. This is your high limit switch. Mar 30, 2011
How do you replace a hot tub control panel?
To replace the control panel is actually straight-forward and easy. Just turn the power of the unit off. Remove the spa access panel and take the cover off the control box. ... Remove the spa topside panel carefully. Place the new one in the same place as the previous one. Plug in the topside wire to the circuit board. More items...
How much is a motherboard for a hot tub?
Hot Tub Motherboard Repair Cost Repairing a hot tub motherboard costs $150 to $450. Feb 4, 2021
How do you reset the Balboa control panel?
Canadian Spa Company Step 1: Turn off the power to the Spa. Step 2: Remove cabinet panel, and covering for the control system. ... Step 3: Locate the heater's sensor wires and trace them to where they plug into the circuit board (pictures below). Step 4: Disconnect the sensor wires from the circuit board. More items... • Mar 29, 2019

How do you drain a strong spa?

Drain your hot tub. Turn the power to the spa off at the circuit breaker. You don't want the pumps or jets to run while there isn't any water in the spa. Next, find your drainage spigot. ... Attach the garden hose to the spigot, being careful not to cross-thread. ... Open the ball valve on your spigot so the water can drain. Jul 2, 2018
How do I get my hot tub out of sleep mode?
On them you need to press the 'TEMP' button and then the 'LIGHT' button within three seconds of each other and this will change the modes from EC (economy mode), to SL (sleep mode) and finally to ST (standard mode) which is what you want. Oct 1, 2011
Are Caldera hot tubs good?
Overall, Caldera Spas is a good spa manufacturer, but it falls a bit short on variety. It does not have the same number of options as most spa brands, and the list of extra features and upgrades is a bit short. It does not offer UV-C or ozone sanitation options, nor do its hot tubs have smart compatibility. Mar 7, 2019
Does a hot tub increase home value?
A portable hot tub really won't add value to your home. It's actually just considered a piece of personal property. However, a hot tub that's built into the ground, with nice landscaping around it, could add significant value to your home.
Are salt water hot tubs better?
Though they carry chlorine, salt water hot tubs and pools are gentler on the eyes, scalp, and skin. It fosters buoyancy, which can be very beneficial in the overall relaxation experience of the hot tub. Salt water does not produce an unpleasant odor. Nov 14, 2019

How do I unlock the Catalina Spa?

All buttons are frozen except the “Time” button. To unlock the panel, press “Time” “Jets 1” then “Cool.” Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm” within 3 seconds to activate the lock. The TL indicator light will light when the set temperature is locked.
How do you unlock a Coleman control board?
Unlock Operating Panel Press the ""Time"" button on your hot tub operating panel. Push the ""Jets 1"" button. Push ""Set down."" A ""0"" will appear on the screen indicating that the operating panel lock is off. The lock symbol will also disappear from the display on the operating panel.
Should I Shock hot tub after filling?
Shock (Optional) If you have time for a deeper cleaning, then it is a good practice to super-shock the hot tub water. This will kill bacteria that are present in the water and allow the purge product to work effectively. Nov 21, 2017
How long after filling hot tub can you use it?
You should wait at least thirty minutes or so. It's also a great idea to put the jets on, this way the water circulates and the water absorbs the chemical better. Additionally, make sure the hot tub cover is off while this happens. This allows any chemical vapors to escape quickly.
How do you clean a Caldera spa filter?
Three To Four Months Remove them from the spa and spray away any debris that has accumulated between the folds with a garden hose. Soak the filters over night in a spa filter degreaser (see package instructions for the product you're using). After soaking the filters, spray them clean and replace. Dec 8, 2017
How do I check the heating element in my hot tub?
You test the element by using an Ohm meter, or any multi-meter will work also. Just place it on Ohms, at 1000, and place your test leads on each of the terminals (power to spa heater should be off). As mentioned above, a measurement of 9-12 Ohms of resistance usually indicates a good element.
What causes heating element to go bad?
If the coil gets too hot, it burns out. Among the conditions that can cause elevated temperatures are insufficient airflow in the element compartment, failure of safety devices and a power surge.

Why does my hot tub get hotter than setting?

A simple cause of hot tub overheating is the hot tub's temperature may be set too high. ... So, if the hot tub is set to filter too many hours per day, it can cause overheating. Adjust your filter cycle duration cycle down and set it to run early AM and late PM, when the outside temperatures are coolest.
What can go wrong with a hot tub?
Here are a few issues that can arise, a lot of which are interrelated: Poor water chemistry. Water in the tub must not be too basic or too acidic. ... Pump seal leaks. ... Clogged drains or filters. ... Burned out motor or circuit board. ... Bad thermostat. Oct 21, 2013
How quickly does a hot tub heat up?
between 3-6 degrees per hour How Quickly Will It Heat? Generally, a hot tub in good working condition will raise the water temperature between 3-6 degrees per hour. To help your hot tub heat quicker, make sure to leave the cover on as heat can escape from the water surface. Feb 22, 2018
How long can hot tub run without power?
3 days *A hot tub can be left without power up to 3 days without risk of freezing, IF you follow these tips: 1. Keep hot tub cover closed and locked in place.
How do you check a hot tub fuse?
Testing Spa Fuses Shut off all power to the spa at the breaker and spa pack. Set your Ohm meter to the 1K setting. Remove the fuse from the board or fuse housing. Place your meter leads on each end of the fuse. Compare readings to printed Ohms level.
Can a hot tub run off a generator?
Yes, you can run a hot tub from a generator but it is probably not the most cost-effective or best solution to the problem of how to power your hot tub. ... You will also need to have the generator on for a long period of time if you are using it to heat the water and so it is also likely to be very expensive to run.

How can I heat my hot tub faster?

You can heat a hot tub faster by turning on the jets, placing a cover over the tub, and using a more powerful heater. These are the easiest and most effective ways to increase your tub's heating speed. It would be best if you didn't fill a tub with hot water.
Does turning down hot tub save money?
Turn Down the Temperature The maximum recommended temperature for a hot tub is 104°F (40°C), but that doesn't mean you have to keep it there. Setting a lower hot tub temperature will save energy and money, and will reduce evaporation, thereby preserving the chemicals in the water. Mar 7, 2019
What temperature should you keep your hot tub when not in use?
A rule of thumb is that the temperature should be at least 5 degrees lower than when in use. It is necessary to keep it at lower temperatures when it's not in use so that energy consumption isn't too high. Oct 12, 2018
How do you test a high limit switch on a hot tub?
On your spa pack you will find a red button that will reset the high limit switch. Once you reset it, test your hot tub to see if it trips again. If it doesn't, the reset did the trick. Feb 21, 2017
How do you test a spa thermostat?
Here are the steps to follow: Check water, filter & overall operation of the hot tub. Make sure there is enough water in the hot tub. ... Check the temperature probe. This is located on the underside of your hot tub. ... Verify the water temperature. Turn the water temperature up to 104° ... Check the back of the thermostat.
What does SPA mode do?
When you want to use the spa you will need to switch your system to "spa mode" which will temporarily change your suction and return manifold valves for your equipment such that water is only being drawn from the spa, and only being returned to the spa.
How do I know if my hot tub has an airlock?
If you turn on the pump, but little to no water comes out of the jets, you have a hot tub air lock. Jan 19, 2021
Do I need to shower after hot tub?
Showering with soap and water before using the hot tub removes bacteria from your body, and removes lotions, deodorants, dead skin cells, etc. ... Shower after using the hot tub as well, to wash off any bacteria, algae, waste, etc. that may have been in the water.
How do you fix LF error on a hot tub?
For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump.
Is it worth fixing a hot tub?
A hot tub is not worth fixing when the cost of the repair is going to be more than the value of the hot tub itself. ... An old hot tub will be significantly less energy efficient than a new one and you could potentially save a lot of money over a period of time with a more energy-efficient hot tub.
What is the spa pack?
The control system, or spa pack, is the brain of the hot tub. This nerve center controls the functions and equipment in the spa, like the jet pumps, filtration time, and heater. There are two types of control systems used in hot tubs: electronic, digital type systems and older-style mechanical air controls.
How much does it cost to replace hot tub jets?
Control systems average $450. Cost to Replace Spa Jets: The cost to replace a spa jet varies from $20-$50 on average. Cost to Replace Spa Circuit Board: Hot tub PCBs range from $200-$600, with an average cost of $300.
How long do hot tub Motors last?
5 to 10 years When it comes to spa pumps, they naturally last from 5 to 10 years. The maintenance that goes into the spa and pump has a lot to do with the longevity of the pump. Think of yourself as your spa's personal trainer, responsible for keeping it healthy and productive.
Can you repair hot tubs?
The simplest ways to repair an inflatable hot tub is with silicone or with a hot tub repair kit. Silicone is often a solution when homeowners don't have an inflatable hot tub patch at hand. Fixing the tub with silicone is easy and inexpensive as most DIYers already have silicone in their tool-set.
Does fix a leak for hot tubs work?
Marlig Fix-a-Leak works exceptionally well on permanently fixing small cracks in the plumbing of the hot tub. It will not, however, fix large cracks or holes in the acrylic shell of the hot tub.
What does PR mean on Balboa hot tub?
Priming The Spa is Operating in ""Priming"" (Pr) Mode. The Spa has just been powered up and is in Priming Mode for 4 Minutes. Pumps and Blower can be turned ON and OFF to Remove any Air from the Heater.
What does EC code mean on hot tub?
If the Ecn or Ec Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Economy Heating Mode. ... The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.
What is rest mode on hot tub?
Rest Mode. When in Rest mode, the spa will not heat unless the filtration cycles are in operation. If the spa is displaying "RUN PUMP FOR TEMP", it is likely in Rest mode and the spa has not circulated for over 1 hour. Mar 31, 2020
How often should you drain your hot tub?
With average use, your hot tub should be drained and refilled about once every three or four months. But since everyone uses their hot tub differently, the answer can vary based on how many people use it and how often. Hot tub manufacturers like Jacuzzi offer some handy tips for figuring out when to drain and refill.
Can you drain hot tub water on grass?
You shouldn't drain your hot tub on your lawn. Spa water contains harmful chemicals like chlorine or bromine that will kill your grass and discolor your well-kept lawn. ... There's more to know about what plants and trees the water could hurt and where you should be draining it.
How do you clean a hot tub without draining it?
How to Clean a Hot Tub without Draining RECYCLE THE HOT TUB INTO THE POOL. This option only works if you also have a swimming pool, or can borrow a neighbor's pool. ... RECYCLE THE HOT TUB INTO THE BATHTUB. ... FILTER SPA WATER THROUGH EXTERNAL POOL FILTER. ... FILTER SPA WATER WITH REVERSE OSMOSIS. ... Balance the Spa Water and Shock. ... SCRUB THE SPA. ... SCRUB THE PIPES. ... SOAK THE JETS.