1. Decide Where You Want to Hang Your Lights. …
  2. Figure Out How Much Rope Lighting You Need. …
  3. Install Plastic Cable Clips. …
  4. Place the Rope Inside the Clips. …
  5. Nail Down Your Cable Clips. …
  6. Plug in Your Rope Lights. …
  7. Turn on Your Lights and Enjoy!

How do you attach rope lights?

  1. Decide Where You Want to Hang Your Lights. …
  2. Figure Out How Much Rope Lighting You Need. …
  3. Install Plastic Cable Clips. …
  4. Place the Rope Inside the Clips. …
  5. Nail Down Your Cable Clips. …
  6. Plug in Your Rope Lights. …
  7. Turn on Your Lights and Enjoy!

How do you hang outdoor rope lights?

  1. Step 1: Measure & Prep. The first thing to do is measure for both your string lights and the cable guide wire you need for spanning across any open spaces. …
  2. Step 2: Mount Screw Hooks. …
  3. Step 3: Connect & Tighten Cable. …
  4. Step 4: Attach Your String Lights. …
  5. Step 5: Sit Back and Enjoy!

How do you hang rope lights DIY?

  1. Step One: Start by securing your rope to the base of your cord with 2 knots.
  2. Step Two: Wrap! Just wrap away, wrapping the length of the rope around the cord. …
  3. Step Three: Secure the end with a knot.
  4. Step Four: Screw in the hangers. …
  5. Step Five: Hang!

Can you hard wire rope lights?

Hardwired rope lighting can illuminate the area under kitchen cabinets. Rope lighting looks like a rope with several small lights inside. … Hard wiring a rope light will free up an outlet where the plug would normally sit. Hard wiring a rope light only takes a few hours and will make it appear professionally installed.

How many rope lights can be connected together?

Therefore, your circuit can only handle 14 incandescent light strings connected together. On the other hand, if an average LED string light set uses 10 watts, then 1440/10=144. That means you can have 144 light strings connected together if they’re LED! That’s a lot more light than the incandescent.

How long do rope lights Last?

Incandescent rope light has the benefit of lower up-front costs and lasts up to 3,000 hours, which is perfect for seasonal use. For long term and landscape lighting projects, LED rope light uses less energy, which allows for longer runs to be connected together. LED rope light is estimated to last up to 100,000 hours.

How do you secure rope lights to the ground?

Lay the stakes on the grass along the light path, spacing them 2 to 3 feet apart. Adjust the stake locations so they are placed at an equal distance apart before inserting them in the ground. Push or hammer the stakes into the ground gently with a rubber mallet until at least half the stake is embedded in the ground.

What size cable do I need for outside lights?

Once outdoors, you should supply your lights via 1.5mm² three core steel-wire-armoured cable (SWA). Make sure that you only fit weatherproof lights that are suitable for outdoor use and that your circuit is RCD-protected.

Can I use PVC pipe to hang string lights?

There are several different ways we could have hung the lights. … It can be a little tricky when hanging lights on a slope. You will want to dig an 18″ hole and then place a PVC Pipe into it. Just make sure it goes below the grass line.

How do you anchor string lights to a tree?

The best way to hang outdoor string lights depends on where you are hanging them. If you have trees, it’s easy to hang lights. Just drill a hole into a tree, install a cup hook, wrap the light around it and secure it with a zip tie. Or you can thread them through the branches and not anchor them.

How do you keep string lights from sagging?

With an attached snap hook and a loose clip that allows you to feed the cable through one side of the clip, loop it around posts and other fixed objects. It’s a perfect solution for large open areas, and to prevent sagging string lights.

Do rope lights get hot?

Do LED rope lights get hot? No. While incandescent rope light generate light by heating a filament, LED rope light use a completely different silicon-based technology that does not produce heat under operation.

Can rope lights be shortened?

Rope light spools can be cut using either sharp scissors or a knife. To cut rope light, measure the area where you plan to install the rope light and then cut the tube at the nearest cutting mark. … This is the only place that LED or incandescent rope light should be cut.

Why are my rope lights not working?

Bad Pin Connection – If your incandescent or LED rope light fails to turn on at all, the first place to check should be your pin connections. … A crooked insertion could cause your rope light to short circuit. Incorrect Cutting – Rope light can be cut and reconnected using splice connectors.

Do rope lights use a lot of electricity?

How much electricity does a rope light use? LED rope lights consume approximately 1 watt per foot of lighting. … LED rope lights also have longer working lives, roughly four times the life span of their incandescent counterparts.